Wuhan Ouyi Optoelectronic Technology Co., Ltd.
Wuhan Ouyi Optoelectronic Technology Co., Ltd. Diligence, pragmatism, efficiency, innovation
Add to Cart
TX1270nm/RX1330nm SFP+ 10GBASE Optical Transceiver Module 60KM Bi-Directional
Applications
10GBASE-LR/LW
CPRI rates 6.144Gb/s, 9.83Gb/s
10Gb/s Fiber Channel
| Supports 9.95 to 11.3Gb/s bit rates |
| Hot-Pluggable |
| Simplex LC connector |
| 1270nm DFB transmitter, 1330nm PIN-TIA |
| SMF links up to 60km |
| 2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface |
| Power Supply :+3.3V |
| Power consumption<1.5W |
| Temperature Range: 0~ 70°C |
PRODUCT DESCRIPTION
SFP-10G is a very compact 10Gb/s optical transceiver module for serial optical communication applications at 10Gb/s. The SFP-10G converts a 10Gb/s serial electrical data stream to 10Gb/s optical output signal and a 10Gb/s optical input signal to 10Gb/s serial electrical data streams. The high speed 10Gb/s electrical interface is fully compliant with SFI specification.
The high performance 1270nm DFB transmitter and high sensitivity PIN receiver provide superior performance for Ethernet applications at up to 60km links.
SFP+10G modules Complaint with IEEE 802.3ae 10GBASE-LR,Electrical interface compliant to SFF-8431 specifications for enhanced 8.5 and 10 Gigabit SFP module “SFP+”,1270nm DFB transmitter, PIN photo-detector,LC connector,2-wire interface for management specifications compliant with SFF 8472 digital diagnostic, Compliant with SFF8472 Digital Diagnostic Standard(DDM)
The SFP+ module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
Optical Characteristics (TOP=25°C, Vcc=3.3 Volts)
| Parameter | Symbol | Min | Typ | Max | Unit | Ref. |
| Transmitter | ||||||
| Output Opt. Power | PO | 0 | 5 | dBm | ||
| Side-Mode Suppression Ratio | SMSR | 30 | dB | |||
| RMS Spectral Width(-20dB) | σ | 1 | nm | |||
| Optical Extinction Ratio | ER | 3.5 | 4.5 | dB | ||
| Tx Jitter(SONET)20KHZ-80MHZ | Txj1 | 0.3 | UI | 3 | ||
| Tx Jitter(SONET)4MHZ-80MHZ | TXj2 | 0.1 | UI | 3 | ||
| Path penalty at 800ps/nm@9.95Gb/s | 2 | dB | ||||
| Relative Intensity Noise | RIN | -128 | dB/Hz | |||
| Center Wavelength | λc | 1260 | 1270 | 1330 | nm | |
| Receiver | ||||||
| RX Sensitivity @10.3 Gb/s | SENS | -16 | dBm | 1,2 | ||
| Receiver Overload | -1 | dBm | ||||
| Optical Center Wavelength | λC | 1320 | 1330 | 1340 | nm | |
| LOS De-Assert | LOSD | -18 | dBm | |||
| LOS Assert | LOSA | -30 | dBm | |||
| LOS Hysteresis | 0.5 | dB | ||||
Notes:
1. Measured with conformance signals defined in FC-PI-2 Rev. 10.0 specifications.
2. Measured with PRBS 231-1 at 10-12 BER.
3. GR-253-CORE Issue 4.
4. With optical input power at the receiver between -1 ~ -11dBm
Recommended Operating Conditions
| Parameter | Symbol | Unit | Min | Typ | Max |
| Storage Temperature Range | Ts | ℃ | 0 | 70 | |
| Power Supply Voltage | Vcc | V | 3.135 | 3.3 | 3.465 |
| Data Rate | Gb/s | - | 10 | - |